Question:
The parking lot of our elementary school is in chaos every morning before school begins, and again in the afternoon when school lets out. In the morning, walkers are mixing with parents dropping off students. In the afternoon, buses sometimes cannot get into our parking lot because so many parents are waiting for their children. I am worried about the air quality around our school due to all those idling vehicles. I am most worried about the safety hazard posed by all those modes mixing in front of our school. What can I do?

–An elementary school principal in northern Minnesota.

Answer:

You can take some comfort in the fact that your school’s situation is not unique; traffic jams surround schools in even the most walkable of neighborhoods.

My first recommendation is to do what you can to reduce demand for those parking spaces. Here is where a Safe Routes to School (SRTS) program can come in handy. Think about conducting a school travel survey of parents to learn more about their attitudes towards SRTS, and to begin the process of identifying barriers to walking to school.

My second recommendation is to move to offsite pick up and drop off locations. This will allow the buses to enter your parking lot. Reducing the traffic around the school will reduce the safety risk to your walkers, reduce the risk of motor vehicle collisions, and the change to an offsite location will eliminate an air pollution hotspot. Perhaps there is a church nearby that will allow the use of its parking lot for this purpose.

My third (and final) recommendation is that you give NCBW a call or consult with the National Center for Safe Routes to School. Each school is unique, so we would be happy to talk to you about your school’s situation, and to point you towards the appropriate resources.

Mark Plotz
NCWB

Denise wrote with a question about railroad track crossings where bicycle accidents were happening:

Q. Hello,
In Harrisonburg, VA, we are having many bicycle accidents at two sites where train tracks ntersect the roadway at very skewed angles and travel along the roadway. We are looking into installing a bulb-out solution, but one of the sites does not have the room for this so we are looking into flangeway filler.

We want to find a company that makes a product that fills all or most of the flange gap so that riders can ride across these places.  Can you recommend something?

Thanks,
Denise Martin
(bicycle advocate)
Broadway, VA

I wrote back and asked what kind of rail traffic was using the crossing. It’s a lot easier to deal with such rail settings than, say, a through route that has trains going faster. I also asked about the roadway’s lanes — how many, what widths? I thought there might be an opportunity to narrow some travel lanes to create some space for a more perpendicular crossing for bikes.

Denise responded: 

…the trains using the crossings in question were freight trains, probably often hauling grain. At one of the crossings, the rail line comes from the south, follows the road and crosses it over a LONG crossing and then follows along the other side of the road.  It is a 5-lane road (one middle turning lane).  The City wants to find a way to make a smooth crossing to benefit all if possible.  Rerouting the road or rail line is completely out of the picture because no one wants to spend that kind of money.  So is placing a bridge over the rails, which I threw in just to make everything else sound less expensive.  Norfolk Southen (the rail company) says the crossings meet “minimum requirements” and if the City wants “upgrades,” they pay.  I say the fix is much cheaper than the medical bills and certainly much less than the cost of a law suit!  Point: Cost IS an issue.  I don’t think anyone would blink about it though if that many motor vehicles were having accidents at a spot. 

The other crossing is on Country Club Road.  This heavily traveled 2 lane road tracks parallel to Route 33.  This is another long, skewed crossing.  Unfortunately the road and trains also go underneath Interstate 81 at the place of the accidents, so there is no room to widen the road or do much else because of the interstate bridge supports on either side of the crossing.I think once they tried to “twist” the road ever so slightly and installed a narrow rubber filler (leaving the 2.5″ inner flange openings.)

We have had quite a few accidents and even broken bones at these places.  Within the past couple weeks a wrist was broken on the Route 11 crossing.  I know of at least 4 very recent accidents there. The local TV weatherman just wrecked his bicycle there and a Harrisonburg police officer wiped out on his police motorcycle!!!  Neither road has a “shoulder” to speak of either.

We wanted to use a compressible flangeway filler to fill the flange gaps.  One company (Polycorp) told me this is not allowed on public crossings (per American Assoc. of RR Engineer’s standards which require the 2.5″ inner flange opening)  I have a few other flangeway filler companies looking into it.  I just discovered HiRail crossings.  They have a pede-STRAIL that is a rubber crossing for pedestrians and cyclists.  The pede-STRAIL rep is on vacation though, so I don’t know if this will fulfill all our needs.  The person I spoke with was not sure it was made to be placed in the roadway.  Their regular crossing is designed for the roadway and could be helpful, but I don’t know if it will eliminate the accidents.

I asked a follow-up question. Denise had mentioned that the crossings are “long,” which suggests a very
shallow crossing angle. I asked if she had any idea at what angle these tracks cross the roadway?

Her response:

Yes, the angle is very unusual on the crossing, but I don’t know that anyone has measured it.  I’ll ask the City engineer about this.  The rails travel mostly parallel to the road and then
gradually cross the road from Left to Right.  The trains then continue on the other side of the road.  A cyclist needs to use up 2-3 lanes on Rte 11 to swing out to make a perpendicular crossing.  Because the road is so busy, cyclists often fail to obtain this much roadway.  On Country Club Road, the cyclist must actually swing out into oncoming traffic to make a perpendicular crossing.  Those that realize this walk or are technically skilled enough to ride it.  However, some of those eventually fall too. Signs warn “Skewed Crossing, Cyclists Use Caution.”  This is a very weak warning in my opinion since most skewed crossings are only slightly skewed.  I have urged the City to put up more strongly worded signs, and they are working on it.  I think they need to acknowledge it for what it is, unfit for a safe
bicycle crossing.

Denise sent some air photos, and gave me some coordinates for Google Earth, which allowed me to zoom in and look around a bit. The angle of the tracks to the roadway did indeed look amazingly shallow. She also told me that she was speaking with the engineer at the rail company, and several meetings had occurred where cyclists, the RR people, and the City had gathered to discuss the situation. THis sounded like it was heading in the right direction.

She added this information:

On the site I had my accident at each rail line has two rails.  The second rail after the flange gap is what bicycle tires seem to push against and suddenly divert left.  This metal rail will be replaced by rubber filler.  “Bulb out” shoulder improvements are supposed to be placed that will allow the cyclist to zigzag across the tracks. (turn right, cross, turn left, remerge).  The turns might be a bit sharp, but the City people wanted to keep the cyclists in the sight line of motor traffic. 

I responded by sending section of the Wisconsin DOT bike facility guide, which does have more details than many of the other guides available. I pointed to images in that guide, one from Seattle where the  rubberized surface is only used toward the right edge of the lane(s). The panels come in sections (4 ft?) and they were able to save some money by only using them where they needed them.  Denise wrote that the WI DOT materials were the single most concise piece she had read yet, and that it tied a lot of info together beautifully. She said she had forwarded the materials I attached on to the city engineers because they were working on finishing the designs. 

And finally came this note from Denise:
Improvements are actually going to be done in the next couple months!!!!  I can’t believe it. I have had quite an education in RR tracks and crossings.  I spent whole days researching solutions and RR products/crossings, so if any info can be passed along, I would love to do this. 

We all learned from this one, Denise! Sometimes the key is that someone takes on the challenge and keeps pushing unitl officials, elected officials, and others recognize the problem and start looking for solutions.

Cheers,
John W.

Brad wrote with this question about getting helmets for distribution in the province of British Columbia.

Good afternoon and greetings from Prince George,
British Columbia, Canada.   Our community
requires that helmets be warn at all times when
biking however many riders do not do so. We are
learning that many don’t wear these simply
because they are without the financial means to
purchase one.  Are you aware of any North
American funding programs that might provide
assistance to obtain helmets for such individuals?

Thank you very much.

 

Brad Beckett
Community Services Supervisor
City of Prince George
Prince George, British Columbia, Canada
250-561-7654

Brad –

I’m cc’ing this message to John Luton of the
Greater Victoria Bicycle Coalition, in case he
has some suggestions for you.

In many communities, the local hospitals help
provide helmets at low — or no — cost. Also,
the ICBC may have some sort of program, although
I couldn’t find it on their website. They do have
a lot of bicycle safety stuff, however. Here are
some of their products.
http://www.icbc.com/youth/youth_new_educators.asp

You should also take a look at the Bicycle Helmet
Safety Institute’s website. This page has
resources, including links to companies that
provide inexpensive helmets.
http://www.helmets.org/toolkit.htm

Hope this helps!
John W.

Laura Willis wrote with this question concerning bicycle rodeos.

Q. Hi, My name is Laura Willis and I am with LeRoy
Christian Church, LeRoy IL. We will
be hosting a bike rodeo to promote biking and
kids health. We were wondering if you might have
anything you could donate. Thanks Laura

A. Hi Laura–

Thanks for your note! Unfortunately, we are a
small not-for-profit organization and do not have
things that would make good prizes for a rodeo.
However, I’d suggest you visit the Adventure
Cycling Association’s website (www.adventurecycling.org) and check out their
bicycle rodeo guide. It has lots of useful tips
on how to make your rodeo more relevant to the
kinds of problems kids have while bicycling. And
it’s only $5 plus shipping. Here’s a link:
http://tinyurl.com/49yz2u

I should admit, though, that I was one of the
authors, so I might be biased!

Cheers!
J